Wisycom receivers are internally coupled by two in a real TRUE DIVERSITY CONFIGURATION. Its front end has a chain of microcontrolled-driven movable filters to allow BROADBAND OPERATION up to 240 MHz with great selectivity.

A powerful low consuption DSP gives you the best of analogue and digital technologies in an hybrid approach for smooth operations, high coverage and with our patented PTT (push to talk) already integrated.

Variant
MCR41 is the version with only one diversity RX board mounted. It supports all features of MCR42 and is compatible with MCR42 Firmware. It is also possible to mount the second Rx board to upgrade a MCR41 to an MCR42.

Dual true diversity in a modular stand-alone or slot-in format.

Switching bandwidth up 240 MHz in the UHF range.

DSP based audio processing for unbeatable audio and digital outputs with our PTT (push to talk) patented technology already integrated.

40 groups of 60 frequencies fully user programmable.

Multicompander operations

Infrared interface for programming and transmitter synchronization

Wisycom exclusive digital sub-carrier telemetry technology allows:

remote TX battery monitoring

tone-squelch operating

PTT function (An optional back-panel module is available, with the secondary intercom output)

Easy setup and operation thru a OLED

Frequency ranges

N option: 470 ÷ 700 MHz

M option: 566 ÷ 798 MHz

Switchable channels

2400 managed in 40 groups ofr 60 frequencies completely user customizable

Switching-window

Up 232 MHz

Frequencies

microprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step;

frequencies is easily PC reprogrammed with optional UPK300E/UPKmini programmer

Frequency error

< ± 2.5 ppm, in the rated temperature range

Modulation

FM, with de-emphasis

Nominal deviation

±40 kHz (Max. operating dev. = ± 60 kHz)

"A" / "B" antenna inputs

with SMA connectors

Antenna input impedance

50 ohm sma type (SWR < 1:2; typ. 1:1.4)

Sensitivity

2 V ( 6 dBV), for SND/N > 58 dB;

5 V (14 dBV), for SND/N > 98 dB

in the whole switching-window*

Amplitude response

< 0.5 dB (RF input sig.: 6 dBV ÷ 100 dBV)

Co-channel rejection

> 2.5 dB

Adjacent chan. selectivity

> 80 dB typical (for ch. spacing 400 kHz)

Spurious rec. rejection

> 100 dB

IF image rejection

> 90 dB

Intermod. rejection

> 76 dB

IIP3

> +10 dBm typical

Spurious emissions

< 2 nW (typical = 0.1 pW)

Noise Reduction system

ENR / ENR-1.2 (Wisycom Extended-NR), noise optimized

ENC / ENC-1.2 (Wisycom Extended-NC), voice optimized & with reduced pre-emphasis

Others, compatible with most systems, thru an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user programmable

AF bandwidth

30 Hz ÷ 20 kHz

Frequency response

± 0.5 dB in the 30 Hz ÷ 19 kHz range

Distortion

MCR42S: 0.3 % typical MCR42S2/S3: 0.1 % typical

SND/D ratio (Analogue)

110 dB typical*

SND/D ratio (AES3)

MCR42S: >125 dB typical MCR42S2/S3: >140 dB typical

Audio output

2 audio line-outpus electronically balanced on two 3 pin mini-XLR Female connector

Audio output level

Adjustable 1 dB step between (peak dev level): -30dBu [MCR42S/S2/S3] /-18dBu [MCR42] to +12dBu [MCR42/S/S2] / +18dBu [MCR42S3]

Audio line-output imped.

200 ohm

PTT line-output 1 & 2

Electronically balanced on a 5 pin mini-XLR Male connector

Digital output

digital line-output 1 & 2 electronically balanced on 3 pin mini-XLR Male connector

Digital sample rate

AES3 @ 48 kHz

POWER LEDs

(NEW display) 1 multicolour RGB LEDs for the power status of the receiver

(OLD display) 2 multicolour RGB LEDs to easy indicate Rx1 & Rx2 power status

RF LEDs

2 multicolour RGB LEDs to easy indicates Rx1 & Rx2 RF status. Always on in normal operation

AUDIO LEDs

2 multicolour RGB LEDs to easy indicates Rx1 & Rx2 audio status

Front buttons

Simple operation with 4 buttons to quickly monitor and setup the receiver.

One touch function for a frequency scan and sync function.

Powering

External = 5 ÷ 18 Vdc (1.5 W max)

Autonomous. = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements)

Power consumption

MCR42 max 125mA @ 12V Approx. 6 hours (with battery pack BCA42)

MCR41 max 95mA @ 12V

Battery life

approx. 6 hours with battery pack BCA42 (5 x IEC-LR6 1.5V size-AA alkaline)

Temperature range

-10 ÷ +55 °C

Dimensions

"Slot-in" execution= 115 x 68 x 18 mm (HxWxD), "Stand-alone" exec.= 135 x 68 x 18 mm (HxWxD)

Weight

180 g approx.

*RMS value, A-weighted, 22 Hz / 22 KHz