The Model 201 Interpreter's Console offers a comprehensive solution tailored for applications requiring simultaneous language interpretation by specialized personnel. Compatible with single or multi-language scenarios, this Dante audio-over-Ethernet-enabled unit boasts advanced features not commonly found in standard interpretation equipment. Equipped to meet the needs of both local and remote deployments, the Model 201 ensures successful implementation across various settings.
Caractéristiques
Creates complete interpreter position
Dante audio-over-Ethernet technology
Supports 5-pin XLR and 3.5 mm TRRS headsets
Two interpret audio channels with feedthrough audio
Talkback function
Slow Down and Hot Mic functions
Stores and replays two confirmation messages
Excellent audio quality
Uses STcontroller for configuration
Power-over-Ethernet (PoE) powered
Spécifications
Applications
Dante-based simultaneous interpretation
Power Source
Power-over-Ethernet (PoE), class 1 (very low power, ?3.84 watts), per IEEE 802.3af
General Audio
Internal Digital Audio Processing: 32-bit, fixed
Nominal Digital Input and Output Level: "20 dBFS
Network Audio Technology
Type: Dante audio-over-Ethernet
AES67-2018 Support: yes
Dante Domain Manager (DDM) Support: yes
Bit Depth: 16, 24, or 32
Sample Rate: 48 kHz
Nominal Level: "20 dBFS
Number of Transmitter (Output) Channels: 4
Number of Receiver (Input) Channels: 4
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Network Interface
Type: 100BASE-TX, twisted-pair Ethernet with Power-over-Ethernet (PoE)
Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s GigE Ethernet not supported)
Compatibility " Headset A: single or dual-ear broadcast- or intercom-style with dynamic or electret (low-voltage DC-powered) microphone: pin 1 mic common; pin 2 mic; pin 3 phones common; pin 4 phones left; pin 5 phones right
Compatibility " Headset B: CTIA?/AHJ configuration (typically uses electret powered mic): tip phones left; ring 1 phones right; ring 2 common; sleeve mic
Microphone Input
Compatibility: dynamic or electret (low-voltage DC-powered)
Type: unbalanced
Electret Microphone Power: 3.3 volts DC via 2 k resistor, selected on/off
Impedance: 1 k ohms, nominal, microphone power off; 680 ohms, nominal, microphone power on
Gain: 24, 30, 36, 42, 48 dB, selectable
Frequency Response: "3 dB at 40 Hz, "1 dB at 16 kHz
Distortion (THD+N): 0.022%, measured at "20 dBFS, 22 Hz to 22 kHz bandwidth, 24 dB of gain
Noise Floor: "95 dBFS, A-weighted, 24 dB of gain
Dynamic Range: >76 dB, A-weighted, measured at 24 dB of gain
Compressor
Threshold: 3 dB above nominal Dante output level ("17 dBFS), ±1 dB
Slope: 2:1
Status LED: compressor active
Confirmation Message Audio
Number of Channels: 2, field updatable using USB flash drive
Headset B: 4-conductor (TRRS) 3.5 mm jack, per Japanese standard JEITA/EIAJ RC-5325A
Ethernet: Neutrik NE8FBH etherCON RJ45 jack (compatible with etherCON CAT5 plug)
USB: type A receptacle (used for updating main firmware and WAV audio files)
Configuration
Studio Technologies' STcontroller personal computer application
Software Updating
USB flash drive used for updating main firmware and WAV audio files; Dante Controller's Dante Updater application used for updating Dante interface firmware
Environmental
Operating Temperature: 0 to 50 degrees C (32 to 122 degrees F)
Storage Temperature: "40 to 70 degrees C ("40 to 158 degrees F)
